User Tools

Site Tools


tutruncart3d

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

tutruncart3d [2012/02/27 22:37]
ramcdona [Run Cart3D]
tutruncart3d [2018/04/01 14:41]
Line 1: Line 1:
-====== Cart3D Execution ====== 
  
-The procedure for running Cart3D with an input file generated in VSP is essentially the same as running Cart3D with any other model. ​ The only special care required is when setting the extent of the domain using '​autoInputs'​. 
- 
-==== Preparation ==== 
- 
-In order to run Cart3D, you must have the following files in a directory where you want to run the analysis. 
- 
-<​file>​ 
-Components.i.tri 
-aero.csh 
-input.cntl 
-</​file>​ 
- 
-If you don't have the [[http://​www.openvsp.org/​files/​input.cntl|'​input.cntl'​]] and [[http://​www.openvsp.org/​files/​aero.csh|'​aero.csh'​]] configuration files, you can go back to the [[TutSetup|Cart3D setup]] page to find out what needs to be done for them, or you can use these links to download ready-to-go versions for this example. 
- 
-If you don't have your geometry in a TRI format, you need to go back to either the Mesh generation or STL to TRI conversion steps of this tutorial and get your geometry in order. 
- 
-  * [[MeshOverview|Mesh Generation]] 
-    * [[TutGenMesh|Isotropic Generated Mesh]] 
-    * [[TutUnint|Unintersected Component Wireframe]] 
-    * [[TutCompGeom|Intersected Component Wireframe]] 
-  * [[TutSTLtoTRI|STL to TRI Conversion]] 
- 
-==== Set Domain ==== 
- 
-The '​autoInputs'​ command is used to set the extent of the domain for Cart3D analysis. ​ In this case, we are modeling a half-domain with a symmetry condition applied to the XZ plane. ​ The following command will set the extent of the domain for analysis: 
- 
-<​file>​ 
-autoInputs -symmY -r 10.0 
-</​file>​ 
- 
-The directory will now contain two additional files which define the extent of the domain (input.c3d) and some prespecified adaptation regions in the domain (preSpec.c3d.cntl). 
- 
-<​file>​ 
-Components.i.tri 
-aero.csh 
-input.cntl 
-input.c3d 
-preSpec.c3d.cntl 
-</​file>​ 
- 
-==== Run Cart3D ==== 
- 
-To run Cart3D with adaptation, simply execute the '​aero.csh'​ in the directory. 
- 
-<​file>​ 
-./aero.csh 
-</​file>​ 
- 
- 
-Or, feel free to jump to your topic of choice. 
- 
-  - [[OneraM6|Geometry Generation]] 
-  - [[MeshOverview|Mesh Generation]] 
-    * [[TutGenMesh|Isotropic Generated Mesh]] 
-    * [[TutUnint|Unintersected Component Wireframe]] 
-    * [[TutCompGeom|Intersected Component Wireframe]] 
-  - [[TutSTLtoTRI|STL to TRI Conversion]] 
-  - [[TutSetup|Cart3D Setup]] 
-  - Cart3D Execution (This Page) 
tutruncart3d.txt ยท Last modified: 2018/04/01 14:41 (external edit)